[. . . ] FS-C8008N FS-C8008DN Color Laser Printer FS-C8008N FS-C8008N Operation Guide Cautions · · To prevent the printer from tipping over, the optional CA-31B caster kit must be installed when the printer is installed with more than one paper feeder or a duplex unit. Do not block the cooling air in and out vents and the exhaust duct against walls or with other objects. If the flow of cooling air is blocked, heat will be built up in the printer, and there will be a risk of fire. Note Moisture condensation inside the printer can cause blurred printing. When a heavily blured printing occurred, turn printer power off while the power cable is plugged to power. [. . . ] The font size can be set between 4 and 999. 75 points, in 0. 25-point increments. The display returns to Ready. 3-48 3. 6 Making Default Settings Character Pitch for Courier/Letter Gothic You can set the character pitch for fixed fonts when the default font is Courier or Letter Gothic. 1 2 Press MENU key. Press the or key repeatedly until Font > appears. Font > 3 Press the key. Press the or key until >Font Select > appears. >Font Select Internal > 4 5 Make sure that Internal is displayed and press the Press the or key. key repeatedly until >>Pitch appears. >>Pitch 10. 00 cpi 6 Press the ENTER key. A blinking cursor (_) appears. >>Pitch 10. 00 cpi 7 8 9 Press the or key to increase or decrease the value at the blinking cursor. The character pitch can be set between 0. 44 and 99. 99 characters per inch, in 0. 01 character-per-inch increments. The display returns to Ready. 3-49 3. 6 Making Default Settings Setting the Code Set You can change the character code set. Press the or key repeatedly until Font > appears. Font > 3 4 Press the Press the key. or key repeatedly until >Code Set appears. >Code Set IBM PC-8 5 Press the ENTER key. A blinking question mark (?) appears. >Code Set ?IBM PC-8 6 7 8 Press the or key until the desired character code set appears. Press the ENTER key. The display returns to Ready. 3-50 3. 6 Making Default Settings Printing Lists of Fonts To help you decide in selecting a font, you can printout lists of the internal fonts or the optional fonts including downloaded fonts. Samples for font lists are shown in Figure 3-8 on page 3-52. 1 2 Press the MENU key. Press the or key repeatedly until Font > appears. Font > 3 4 Press the key. Press the or key repeatedly until >List of Internal Fonts or >List of Option Fonts appears. >List of Internal Fonts 5 Press the ENTER key. A question mark (?) appears. >List of Internal Fonts? 6 Press the ENTER key again. The printer prints out a list of fonts with a sample and font ID (number) for each of them. Sample lists of fonts are shown in Figure 3-8 on the next page. 3-51 3. 6 Making Default Settings Internal Scalable and Bitmapped Fonts List Font Name Scalable/Bitmap Password Selection [FSET] PRESCRIBE Font ID Internal Scalable and Bitmapped Fonts List Font Name Scalable/Bitmap Password Selection [FSET] PRESCRIBE Font ID Figure 3-8 3-52 3. 7 Pagination 3. 7 Pagination In Page Set menus, you can set the number of copies, page orientation, and other settings regarding pagination. 3. 7. 1 Number of Copies You can set the number of copies of each page to be printed for the current interface. The number of copies can be set between 1 and 999. 1 2 Press the MENU key. Press the or key repeatedly until Page Set > appears. Page Set > 3 4 Press the Press the key. or key repeatedly until >Copies appears. >Copies 001 5 Press the ENTER key. A blinking cursor (_) appears. >Copies 001 6 7 8 Press the or cursor. Use the key to increase or decrease, respectively, the value at the blinking and keys to move the cursor right and left. When the desired size is displayed, press the ENTER key. The display returns to Ready. 3-53 3. 7 Pagination 3. 7. 2 Print Orientation You can select portrait (upright) or landscape (sideways) page orientation. Portrait Orientation Landscape Orientation A A Figure 3-9 1 2 Press the MENU key. [. . . ] If you have an IBM communications adapter cable type 1502067, use the procedure below to solder the wiring at the end (printer side) of the cable: 1 2 3 4 5 6 7 8 B. 5. 2 Unscrew the plastic cover at the end (printer side) of the cable. A bare shield wire is provided for each wire in the cable. Connect the bundled shield wires to the connector metal face using a piece of flat cable about 3 mm wide and 15 mm long, . Unsolder wires 2 and 3, then resolder them in a crossover configuration. Cut wires 4, 5, 6, and 20. Solder wires 5 and 6 together and connect them to pin 20. [. . . ]